PUNCH PRESS TOOLS

Vol.1   COUNTERMEASURES FOR SLUG PULLING
Vol.2   LIFE COUNTERMEASURE FOR TOOLING
Vol.3   TOOL MAINTENANCE
Vol.4   FORMING TOOL
Vol.5   MATERIAL FOR TOOLING
Vol.6   FOR CLEARANCE OF THE CUTTING DIE
Vol.7   ABOUT TURRET PUNCH PRESS MACHINE
Vol.8   VARIOUS KINDS OF SPECIAL SHAPE
Vol.9   PARTS NAME OF STANDARD TOOLING
Vol.10   EACH NAMES OF FORMING TOOL
Vol.11   MATERIAL PROPERTIES (STEEL)
Vol.12   MATERIAL PROPERTIES
Vol.13   CALCULATION FORMULAS FREQUENTLY USED IN SHEET METAL
Vol.14   HEIGHT ADJUSTMENT FREE TOOL
Vol.15   HOW TO DRAW AND READ DRAWINGS
Vol.16   HOW TO DRAW AND READ DRAWING (PRACTICAL USE)
Vol.17   SHAPE INSTRUCTION FOR FORMING TOOLS(1)
Vol.18   SHAPE INSTRUCTION FOR FORMING TOOLS(2)
Vol.19   CODE MANAGEMENT
Vol.20   BENDING TECHNICAL INFORMATION
Vol.21   TECHNICAL COUNSELING FAQ(1) "COUNTERMEASURES FOR GALLING"
Vol.22   TECHNICAL COUNSELING FAQ(2) "BURRING FOR THREAD FORM"
Vol.23   TECHNICAL COUNSELING FAQ(3) "PITCH OF SINGLE PIERCING"
Vol.24   TECHNICAL COUNSELING FAQ(4) "SHEAR OPTIONS"
Vol.25   TECHNICAL COUNSELING FAQ(5) "HOLDING MARK"
Vol.26   TECHNICAL COUNSELING FAQ(6) "SOLUTION FOR SLUG PULLING OF A SHEET METAL WITH PROTECTIVE FILM"
Vol.27   TECHNICAL COUNSELING FAQ(7) "MATERIAL WARPING PREVENTION DURING"
Vol.28   TECHNICAL COUNSELING FAQ(8) "WARPING PREVENTION OF BLANKING OUT"
Vol.29   TECHNICAL COUNSELING FAQ(9) "COUNTERSINK FOR COUNTERSUNK SCREW"
Vol.30   THE ORDERING GUIDE(1) "HOW TO INSTRUCT SHAPE AND DIMENSIONS"
Vol.31   THE ORDERING GUIDE(2) "REFERENCE KEY DIRECTION"
Vol.32   THE ORDERING GUIDE(3) "ANGLE INDICATION OF ANGLED TOOL"
Vol.33   THE ORDERING GUIDE(4) "SELECT SPECIFICATION OF PUNCH"
Vol.34   THE ORDERING GUIDE(5) "DIE SPECIFICATION SELECTION"

  FORMING TOOLS

FORMING TOOL TECHNICAL INFOMATION

• 1)HALF SHEAR (SHEAR BUTTON)
• 2)EMBOSS (DIMPLE)
• 3)COUNTERSINK FOR COUNTERSUNK SCREW (CHAMFERING)
• 4)COUNTERSINK
• 5)COUNTERSINK BURRING
• 6)ONE PITCH THREAD FORM
• 7)BURRING FOR THREAD FORM
• 8)BURRING
• 9)CURLING
• 10)EMBOSS
• 11)CENTER POINT
• 12)KNOCKOUT
• 13)BRIDGE, DOUBLE BRIDGE
• 14)LANCE (Z-BENDING)
• 15)LANCE (L-BENDING)
• 16)LANCE FOR AIR FLOW
• 17)LOUVER FOR AIR FLOW
• 18)BEADING
• 19)CARD GUIDE
• 20)BENDING (OFFSET TOOL)
• 21)MARKING (STAMPING)
• 22)MARKING (EMBOSS)
• 23)PROJECTION
• 24)HINGE TOOL
• 25)SPECIAL TOOL USERS MANUAL (AMADA TYPE)
• 26)SPECIAL TOOL USERS MANUAL (MURATA TYPE)
• 27)TOOLING STRUCTURE AND PARTS NAME (AMADA TYPE)

MOVIE

• 1-1)HALF SHEAR (SHEAR BUTTON)
• 1-2)EMBOSS (DIMPLE)
• 1-3)COUNTERSINK FOR COUNTERSUNK SCREW (CHAMFERING)
• 1-4)COUNTERSINK
• 1-5)COUNTERSINK BURRING
• 1-6)ONE PITCH THREAD FORM
• 1-7)BURRING FOR THREAD FORM
• 1-8)BURRING
• 1-9)CURLING
• 1-10)EMBOSS
• 1-11)CENTER POINT
• 1-12)KNOCKOUT
• 1-13)BRIDGE, DOUBLE BRIDGE
• 1-14)LANCE (Z-BENDING, L-BENDING)
• 1-15)LOUVER FOR AIR FLOW
• 1-16)BEADING
• 1-17)CARD GUIDE
• 1-18)BENDING(OFFSET TOOL)
• 1-19)MARKING (STAMPING, EMBOSS)

PRESS BRAKE TOOLS

• Vol.1TYPE OF PRESS BRAKE TOOLS
• Vol.2ABOUT V - BENDING TYPE
• Vol.3PREPARATION FOR BENDING 1
  (TONNAGE CHART , MINIMUM FLANGE LENGTH, V width selection)
• Vol.4PREPARATION FOR BENDING 2
  (Punch marking example, V - BENDING FORCE CALCULATION FORMULA)
• Vol.5THE FEATURES OF BENDING
  (BENDING ALLOWANCE, SPRING - BACK)
• Vol.6ABOUT TOOL SELECTION
  (STEPS FOR CHOOSING A TOOL, STUDYING FROM THE DRAWINGS, READ DETAILS FROM DRAWINGS)
• Vol.7ABOUT TOOL INSTALLATION
  (TOOL INSTALLATION PROCEDURE, ALIGNMENT PROCEDURE)
• Vol.8PROBLEMS OF BENDING
  (DIMENSIONAL DEFECT AND ANGLE DEFECT, GUIDELINS FOR RE-POLISHING, COUNTERMEASURES OTHER THAN REGRINDING)